Hey guys!
need some advice on fishfinder installation,
how do u guys install the transducer?
do u glue it in a foam inside your kayak???
Is it accurate like that?
How do u power your unit?
12 volt battery???
I'll take any ideas!
Thanx
LennyD
Printable View
Hey guys!
need some advice on fishfinder installation,
how do u guys install the transducer?
do u glue it in a foam inside your kayak???
Is it accurate like that?
How do u power your unit?
12 volt battery???
I'll take any ideas!
Thanx
LennyD
Lenny found this on youtube. I added the specific questions and the answers. Hope this helps.
Do you specifically need a through hull transducer or does the application of goop allow you to use any transducer? Thanks a lot for the vid. Big help.
did u Goop the transducer to the interior floor or the bottom of the kayak
Sorry about the deal...
It is glued to the inside of the hull, centered under the cockpit of the kayak.
Great video.Did you just stick that transducer to the floor of the kayak?Please help me lol.New to kayaking and dont reele no what im doing.lol
Really easy...
Just find a centered spot inside the hull, and rough it up with sandpaper. Then glue down the puck. Make sure there are no air bubbles in the glue though, or resolution will be affected.
great video, one question though did you push the transducer to the floor of kayak or just suspend it in the goop?? as i want to fit transducer to my yak but unsure as have seen vids showing it pushed to the floor.
thanks
paul
I push it all the way down in the Goop. Make sure there are no air bubbles between it and the floor too.
hey fishyaker im new to the yake fishin i just bought a old town angler edition sit in kayak this month i have a lowarnce dx50 fish finder but no where to mount it with out it setting cocked could u help me out
If you feel like you have some extra cockpit space, take some plexiglass and make a small flat dashboard at the front of the cockpit.
Hi Lenny I'm new to the forum but was looking into installing fishfinders on kayaks myself. I came across this so I thought it might be of help to both of us. I guess we should all be careful to read the directions that come with the fishfinders. Especially since it has to do with drilling hole in our kayaks.
Fishfinder Installation
Click on images to view largerIMPORTANT Read and understand manufacturer's instructions for installing their unit BEFORE proceeding with this installation. This installation will show you how to mount a transducer, put cables through the deck (and make it water tight), to tuck the cables inside the hull and install the battery box.
Mounting the transducer: Turn the kayak over and find the flattest area of the hull. This is where you will want to mount the transducer on the inside of the hull close or next to the scupper holes (which is the strongest area of a hull and has the least amount of flex) that you can easily reach. Using emery cloth (150) lightly sand to rough up the area where you are going to mount the transducer. Wipe area clean with a rag. Most manufacturer's recommend using a two-part, slow cure epoxy. This works well on a hard surface, but most kayaks area made of plastic and are flexible. "Marine GOOP" is a silicone based adhesive and will give and stretch with the bumps of the road, waves, and other movements.
http://www.kayakfishinggear.com/imag...nder-10-tn.jpghttp://www.kayakfishinggear.com/imag...nder-22-tn.jpghttp://www.kayakfishinggear.com/imag...inder-4-tn.jpgUsing "Marine GOOP" cover the bottom of the transducer with no air bubbles in the GOOP. (About the size of a quarter for the transducer shown. Your brand may require more GOOP) . Place the transducer on the area pressing down and moving it from side to side just a little bit until it is all the way down against the hull. Now place a weight on top of the transducer and let it dry for 24 hours. The kayak must be sitting level or the transducer will start moving.
http://www.kayakfishinggear.com/imag...nder-17-tn.jpg
Check to make sure that the transducer doesn't move during drying
Mounting Display Unit: Before mounting your fishfinder, mount your rod holder(s) first and then select an area suitable for your display unit. Locate a suitable area for the display unit (photo A). Drill hole just big enough to fit plugs through. (Photo B below shows drill bit and plugs and photo C shows the mount with the hole drilled into kayak).
A
B
C
BE VERY CAREFUL WITH THE KNIFE in this next step. Using a rubber stopper, you will make a grommet. Cut stopper in half (See photo D). Cut two grooves about 1/8" deep all the way around and 1/8" apart (Photo E). Now make a trough in the stopper (Photos F shows it started and photo G shows it complete. Click on images to see them larger). Now Drill 2 or 3 holes in the stopper depending on the unit you have. Use a drill bit just slightly bigger than the cable (See photo H). Slice the stopper from the outside to the holes from 2 or 3 different sides (see photo I). Now you have a custom grommet. Pull cables through the hole in the deck and put them into the grommet (see photo J). Using a screwdriver, work the grommet into hole (see photo K). It should look like Photo L now. Also see picture M for the inside view. Now mount the base. Note: I like to use nuts and bolts for all mounts when I can reach the inside area see photo N)
D
E
F
G
H
I
J
K
L
M
N
Mounting the Battery Box: Cut a pool noodle in half (the width of the box) and using GOOP glue this to the back of the box (See photo O). Let dry for 24 hours with weight on top of the box (the battery works well for this). Place the box inside the front of the kayak. Using a felt tip maker, run the marker along the hull while marking the pool noodle (see photo P). Trim the pool noodle down the line, stay to the outside of the line. (see photo Q).
P
Q
Place the battery into the box and using GOOP secure the pool noodle to the box (see photo R). Let this dry for 24 hours. Drill a hole in the box for the cable and secure it with a plastic cable clamp (see photo S). Using an emery cloth, rough up the area and wipe clean. With the battery in the box for weight, use GOOP to glue the box down in the hull. Let this dry for 24 hours. During the first hour check every now and then to make the battery box is not sliding. Now put a water tight fuse and two female flat connectors to the wires (see photo T).
R
S
T
The last thing to do is to tuck the cables up and secure them using zip ties, rubbing alcohol and zip tie anchoring attachments. Sometimes the peel-and-stick zip tie attachments do not work well on certain kayaks, so you would want to use the plastic cable clamps attaching them to a mounting bolt on the inside of the kayak
http://www.kayakfishinggear.com/inde...n=Custom&ID=13