Results 1 to 6 of 6

Thread: Repairing or rebuilding Garcia Mitchell reels

  1. #1
    Join Date
    Jul 2009
    Posts
    6

    Default Repairing or rebuilding Garcia Mitchell reels

    I have a 300 and I let my 10 year old try it.........he clicked the bail over when it was in the wrong spot and that was the beginning ......I had to take it apart to fix the Bail Spring and so I thought.....I had not cleaned it in a long time(don't try to fix what is not broke) anyway...I took it all apart and gave it a cleaning and put a few drops of reel oil here and there....put it all back together and it was spinning like a champ. Took it out to use it a few days later just to be sure it was OK...all went well until I tried reeling in the line....for some reason it went almost a full turn on the handle and then jammed up. It would not go forward or back.....I am wondering if I somehow lost a shim......I don't know what to do ...and the schematic I find on this site is not very clear to show where shims are supposed to be....anyone have any help??? thanks

  2. #2
    Join Date
    Jun 2009
    Posts
    639

    Default Repairing or rebuilding Garcia Mitchell reels

    Zorthedog, Welcome to the site. There are lots of good people here. Maybe someone else will also chime in.

    I don't know much about reels but figured I would do some searching to see if I could help you out. I came across this. He took some good pictures and gave details.

    Will probably take two posts for me to put it up. If it is not what you are looking for let me know and I can try to search some more.


    Cleaning and Repairing a Garcia Mitchell 300 Spinning Reel


    When I was a kid many years ago, my dad and I used to fish in salt water occasionally. He believed that anything we used in salt water needed to be cleaned thoroughly and as soon as possible after our trips. When I got old enough that he thought I could handle it, he started me to cleaning our rods and reels. When I would do this, I would first take all the reels that had been exposed to the salt water and soak them in a bucket of fresh water for an hour or so. Then I air dried them with compressed air, that usually got most of the damaging salt off of the external parts of the reel. Then I would wipe them down with gun oil and put them away. About every other time we went to the salt water I would take them apart, clean and repair them as necessary. I am still using a couple of those reels today. Hopefully I will show in this post how to do this to a spinning reel. I am going to use a Garcia Mitchell 300 reel that was manufactured in approximately 1960. It is well used as you will see, but works like a new reel for me. I must note that I have a pretty extensive parts supply, but everything I use is available through most reel repair shops. Except for the unique gearing in a Mitchell 300, most spinning reels are similar and just as easy, or easier. I never tear a reel down any farther than necessary to clean and lube it. Most reels only need to have the spool removed and the side plate taken off to gain access to all the parts that require grease or oil. When you buy grease be sure that it is a type that will stay the same viscosity at all temperatures, so it won’t get stiff during the cold months. I made the mistake of using bearing grease once while in Colorado and had to cut a trip short because the reel got so hard to turn. Lesson learned! For a couple of bucks, I decided I could afford some reel grease. Any of the brands made for reels should work fine. The oil can be reel oil, gun oil or any good household oil such as 3 in1 oil. When I do a thorough cleaning, I use paint thinner to clean the gears and bearings. Make sure that the bearings are the very first thing you put in the thinner, that will ensure that it is really clean when you are done. It doesn’t take much dirt to make a gear get rough and noisy. And try not to get any of the thinner on the painted surfaces, it will turn the paint white, it isn’t permanent, but sure looks bad at the time.



    This is of course, a Garcia Mitchell 300.


    Take the spool and handle off the reel and set them aside.


    Next remove the bail and bail return spring (only if it’s necessary) Note how the spring comes out, so it can be put back correctly later.


    Now remove the side plate and note where all the gears and the anti-reverse dog are located in the housing.


    Now take all the gears and anti-reverse dog off the side plate and set them aside. Notice all the worn parts, what keeps the reel working good is the shims you see in the next few pics. If you own one of these reels, the shims can keep them working like new almost indefinitely.


    A better pic of the shims, keep track of where they go and don’t mix them up, even if they look exactly the same as shims from a different part of the reel. The shims are sized for the exact diameter of the shaft or gear post they go on. The discoloration in the side plate is old grease and not rust. Most of the wear you see is from the previous owner, I bought this reel at a yard sale for $5.00. I then put about 2 bucks worth of shims, grease and time into it. I have been using this particular reel for about 2 years.

  3. #3
    Join Date
    Jun 2009
    Posts
    639

    Default

    Continued from previous post:

    Continued from previous post



    The gear and slider shown here are what controls the shaft movement. Take the gear out and set it aside for now.


    The slide plate that has all the brass showing on it has a small post on the other side that inserts into a hole in the shaft. When you reassemble this part, make sure it is toward the back of the reel.


    Next take out the slider plate and remove the shaft. Set these parts aside.


    What you see here is the inside of the rotor, the plate is what trips the bail release.


    Next remove the center nut and take the plate out and the rotor of the reel body. (I only disassemble it this far for a thorough cleaning). When you remove the plate, there may be shims under it, as stated before, keep track of which shims go back. There are also probably shims under the rotor itself. This combination of shims is what determines how much head play is in the reel. Unless there is a very obvious reason, this is as far as I ever tear down a reel, not even this far if I’m just going to grease it. Now you can wipe all the parts down and clean them with the paint thinner. Apply grease to every gear and moving/sliding part of the reel as you reassemble it. Apply oil to all the external moving parts such as the bail release and the bail itself. If the reel worked good and didn’t make any rubbing/rough noise when you disassembled it, then make sure you get all the shims back in their original locations. If the reel sounds like the gears are rubbing against the housing, then add a shim(they are available from reel repair shops) to only one gear at a time to see if it has an effect on the noise. Add only one at a time until it turns freely and quietly. If the rotor has an excessive amount of play, you can sometimes just remove a shim from under the plate or rotor and get it right. Just make the rotor turns freely when you are finished. It’s just a matter of making an adjustment, trying it out and see if it worked or not. If not, then do it again until it's right. The spool seldom ever needs anything other than cleaning, sometimes I will put some oil on the center shaft of the spool if it doesn't feel right. It is very simple if you pay attention while taking it apart.

  4. #4
    Join Date
    Jun 2009
    Posts
    639

    Default

    Continued from previous post



    Have you ever been fishing and had the reel work fine one minute and the next the bail wouldn’t return all the way back? Usually this is caused by a bent bail, the next 2 pics show how to fix this small problem. This can be caused by a lot of things, but it is usually very easy to fix.


    As you can see in the pic, the bail on this reel is bent out a good bit. If the screw was in, it would probably not return all way back when the reel is turned. The bend puts a good bit of pressure on the mount points of the bail. Always make this adjustment on the opposite side of the bail that the return spring is located on.


    Just very slightly and carefully bend the bail in small increments until it is sitting in it’s proper position without the screw in it. It should be just above the mount point, and stay there when pulled back for casting without the screw installed. Once you have it in this position, install the screw and make sure it moves freely when the screw is tight. That’s all there is to it. It’s the most common problem with a spinning reel. Note in the last pic there is a different handle on the reel, the one that was on it was slightly bent so I put a handle from a newer reel on for now.

    That’s it. There’s really not all that much to maintaining one of these fine old reels. I have somewhere in the neighborhood of 25 of these reels. Mostly 300’s but also 400’s and 410’s as well. I also have the salt water series of these reels the 306, 302 and 402 as well as the ultra light series, 308 and 408. Most of my reels are more than 30 years old and all work like new. I usually get them at flea markets, yard sales and pawn shops and I won’t pay more that $10.00 for one. I used to buy them off eBay until it got so commercialized, with shipping I bought 3 reels one time for $7.50. Probably not many of you use this type of reel, but if you do I hope this article is of some use.

    Now someone needs to post a “how to” for Daiwa type baitcasters, I have two of these. I started to disassemble one once and got the 4 screws out of the handle side, took it apart, saw the 14 million little parts and promptly put it back together again and felt fortunate that it still worked. Even with the diagram I am not brave enough to do it.


  5. #5
    Join Date
    Feb 2008
    Location
    New Jersey
    Posts
    1,272

    Default

    Quote Originally Posted by zorthedog View Post
    for some reason it went almost a full turn on the handle and then jammed up. It would not go forward or back.....I am wondering if I somehow lost a shim......I don't know what to do ...and the schematic I find on this site is not very clear to show where shims are supposed to be....anyone have any help??? thanks
    Zor those Mitchell reels are not the most complicated but you still have to be careful and take your time. It seems to me the most likely culprit is a spring that somehow was not installed correctly. You can fix this, but you need to be patient.

    Set up a reasonable work space where you will not be disturbed. A table with good lighting is a must. As you get older, like me, you will appreciate this even more. Get a copy of the diagram and enlarge it as big as you can (again a tip mostly for us seniors). Slowly and carefully begin to disassemble the reel. This is where your patience will come into play. Make sure you have enough time to strip it down. If you are a good detective, by looking at the diagram as you disassemble it you will slowly begin to see your mistake unraveled.

    Did you clean and lube everything carefully? If not now would be a good time to do it. Also if you have any springs or pieces that look worn now would be the time to replace them. Do not start putting that reel back together untul you have determined which parts are worn and need replacement. That would be like repairing a motor of a car by using old pistons. Carefully put the pieces back together according to the diagram. Double check your work at each step of the process. This is the part where a lot of folks make mistakes, you have to make sure not only do the parts fit together, but that the action will be as intended. If there is any binding or tightness at any stage, you must figure out where you went wrong.

    If you really get to the point where you feel it's useless, you could bring the reel to any of several shops to be serviced. I don't know what area you are in, but we have some reliable tackle shops in New Jersey. Good luck, take your time, and follow the diagram exactly. You can do this, Zor. And welcome to the site. Why not tell us a little about yourself and how you came to be a fisherman when you get a chance? Where do you fish out of? What do you primarily fish for?

  6. #6
    Join Date
    Jul 2009
    Posts
    6

    Default

    Thank you all for your help on this .....I sat down and went over the Reel once again and this time I really cleaned it well. Upon removing all the "grease" I noticed 2 things ...(1) the slide and the Pivot Gear were binding a little...upon closer look, the Pin that the Pivot Gear went on was loose. (2) I also noticed that the Driving gear was missing 1/2 of a tooth, which I think most likely goes back to the loose pin that the Pivot Gear sat on.....So in conclusion...I found a nice guy on Ebay that had gear sets for sale for a very reasonable price and for under 20 bucks I have replaced all the parts and the Reel is working again. I have had this Reel for 27 years and only retired it because me 3 sons bought me a Pflueger Reel for Fathers day .....I still like my Mitchell though...even though the new reel is smooth as can be....I just don't seem to like the feel of it......now I may retire it and use the good old Mitchell again since it it working great again. Maybe some day I will pass it down to one of my boys. Thanks again for your help, and keep fishin!!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •