Results 1 to 11 of 11

Thread: Plug repair

  1. #1
    Join Date
    Oct 2008
    Location
    NJ
    Posts
    3,962

    Default Plug repair

    Not sure if this is where this thread should be.
    Regarding a winter project.
    These plugs need some repair work.
    Any helpful hints?

    Click image for larger version. 

Name:	PC260001A.jpg 
Views:	1 
Size:	25.1 KB 
ID:	8942
    Click image for larger version. 

Name:	PC260004A.jpg 
Views:	2 
Size:	28.0 KB 
ID:	8943
    Cracked.
    Is just epoxying this one all that is required?
    Will it be OK then or is it shot?

    Click image for larger version. 

Name:	PC260007A.jpg 
Views:	0 
Size:	32.8 KB 
ID:	8944
    Click image for larger version. 

Name:	PC260008A.jpg 
Views:	2 
Size:	36.8 KB 
ID:	8945
    White Water Monty 2.00 (WWM)
    Future Long Islander (ASAP)

  2. #2
    Join Date
    Dec 2008
    Location
    from New Haven live in Wallingford Ct.
    Posts
    1,884

    Default fix

    Quote Originally Posted by Monty View Post
    Not sure if this is where this thread should be.
    Regarding a winter project.
    These plugs need some repair work.
    Any helpful hints?

    Click image for larger version. 

Name:	PC260001A.jpg 
Views:	1 
Size:	25.1 KB 
ID:	8942
    Click image for larger version. 

Name:	PC260004A.jpg 
Views:	2 
Size:	28.0 KB 
ID:	8943
    Cracked.
    Is just epoxying this one all that is required?
    Will it be OK then or is it shot?

    Click image for larger version. 

Name:	PC260007A.jpg 
Views:	0 
Size:	32.8 KB 
ID:	8944
    Click image for larger version. 

Name:	PC260008A.jpg 
Views:	2 
Size:	36.8 KB 
ID:	8945
    hello salty brother,shoot me some pix,chances are we can fix 'em.

    R-P
    Takes a Big Man to sling Big Wood,,,,boys sling plastic,,,,,,,

  3. #3
    Join Date
    Feb 2008
    Posts
    1,541

    Default

    On the first white one, it could have cracked because something happened that it didn't dry completely before they started working on it. No offense to the builder, sometimes it happens even with the best of plugs. I would hand sand it down with rough sandpaper going to fine, and feather edge the areas around the crack without changing the outside dimensions of the plug too much. Then set up some e-tex or maybe an epoxy paint from a spray can if you don't have a gun. Use very light coats at first covering the whole plug but mostly the affected area. Don't allow it to run, hence the reason for the light coats.
    As for the hook holders that got pulled out, nice fish.
    I would put them back, fill with plastic wood in the deepest part inside to fill it in. Leave a slight depression and fill with self-hardening epoxy. Be careful to use a toothpick for the epoxy so it doesn't interfere with the movement of the hook. You just want to concentrate it under the grommet, and the plastic wood will make it firmer inside. Once that dries, sand down carefully, and re-seal with epoxy paint again.
    You can also use clear acrylic from a can, but the finish won't last as long. Hope this helps.

  4. #4
    Join Date
    Sep 2008
    Location
    NJ
    Posts
    2,439

    Default

    What ledhead says. It also depends on the plug. I have some that are bluefish beaters. For ones like that, I would put them back together as quick as possible and not worry about the liquid wood and all that. A quick dab of epoxy gel, let it harden, seal up if you want with one coat of clear from a spray can, and you're done.

    The most important advice I can add is change your hooks to vmcs if your points are dull. It's a heartache to lose a fish due to a pulled hook. It's also a bummer if your hooks weren't sharp enough and you missed your season't best fish because of it.

  5. #5
    Join Date
    Mar 2009
    Posts
    531

    Default

    I have had grommets pull out. Just dab some epoxy on it and stick it back in place. It will hold.

    I don't know about the cracked plug. It may just need some sanding and epoxy. I had used a Mag Darter with the as s end split and used it until the through wire was bent too much to use any more.

  6. #6
    Join Date
    Dec 2008
    Location
    from New Haven live in Wallingford Ct.
    Posts
    1,884

    Default

    Quote Originally Posted by Rip-Plugger View Post
    hello salty brother,shoot me some pix,chances are we can fix 'em.

    R-P
    did we ever fix this one?,,,I don't rememeber if we did,if not and you still have the plug I know how to fix it.
    Takes a Big Man to sling Big Wood,,,,boys sling plastic,,,,,,,

  7. #7
    Join Date
    May 2009
    Location
    Keyport NJ
    Posts
    584

    Default


    this was throw away ....I added the lip back ...I didn't want to paint the wood ..wanted the epoxy to soak into the repair ...better than new
    Attached Thumbnails Attached Thumbnails fin plug fix.jpg   fixed plug.jpg  


  8. #8
    Join Date
    Mar 2008
    Posts
    1,569

    Default

    Wow that's an incredible fix. How did you do that if you don't mind me asking? It looks like you added wood to it but that's not possible is it?

  9. #9
    Join Date
    Mar 2008
    Posts
    1,058

    Default

    I would like to know as well. Awesome repair how did you make it happen- epoxy?

  10. #10
    Join Date
    Dec 2008
    Location
    Long Island,N.Y.
    Posts
    2,581

    Default

    either wood filler or a plumbers epoxy lay it in and sand away and repeat until you get the shape back apply epoxy good as new most of the time.Plugs with wooden lips I prefer wood filler to keep the weight closer to the original,epoxy can get heavy an throw off the action on those type of plugs.Another tip using epoxy is to not sand it any finer then 150 grit because anything finer will not allow the epoxy to grab property resulting in a crack and also sand lightly in between coats.Make sure the plug is free of dust at all times wearing vinyl gloves to keep the oil from your fingers off the epoxy or you get the famed fish eye.
    Cranky Old Bassturd.

  11. #11
    Join Date
    May 2009
    Location
    Keyport NJ
    Posts
    584

    Default

    no wood filler ....just grind the clip away to a flat area ....epoxy in a larger piece of wood in ...which hangs over every edge .....sand to couture the lip ....then I sanded the plug and used glitter technology to finish it off ....I wanted the epoxy to soak into the new wood and joint to made it stronger ...could of primed it ...then used glitter technology ....something I don't fish ....gave it back to the kid that threw it out

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •